- Use a network cable or WIFI hotspot to connect your computer/mobile phone to the router.
- 2. Then, type your PSK password (WIFI password).
The IP address 192.168.1.25 is a private IP. Various brands and models of routers generally use it as their gateway address.
The administrator access to the router is usually set up using this address to configure it and the network. And there also are some routers that do not use 192.168.1.25 as a login address.
And, sometimes, when logging into the router with 192.168.1.25, we commonly encounter various problems.
So, here are the solutions to some familiar 192.168.1.25 Admin Login Page, Username, and Password problems.
192.168.1.25 Login Page
The IP address 192.168.1.25 is used as an access point or gateway by routers such as Linksys and other network brands. Companies provide admin access to routers and networks via this address.
And one can manage Security Options, Network Management, IP QoS, DNS, proxy, LAN, WAN, WLAN settings, DSL, ADSL, MAC, WPS block; amongst others using it.
How to Login 192.168.1.25
You can access your Router Admin software through a 192.168.1.25 IP address to make changes to its settings and configurations. Simply, in the address bar of your browser, type 192.168.1.25.
192.168.1.25 is not your router’s IP address if it does not work. So, type the router’s IP address into your browser’s URL address.
And then, you will be redirected to the user login page. Here, enter your router username and password.
Following these instructions, you can retrieve your username and password if you forget them.
You can also use our router default usernames, and passwords list if you haven’t changed the default user and password that came with the router.
The router’s internet settings can be modified once you are in the router’s admin panel.
How to Use 192.168.1.25 to Log in to the Router’s Administration
According to the above introduction, the router’s login address is 192.168.1.25. But, how do you log into the router’s administration page?
Follow the instructions below.
1. Use a network cable or WIFI hotspot to connect your computer/mobile phone to the router.
2. Launch your preferred web browser, like Edge, Chrome, etc.
Now, in the address bar of your browser, type 192.168.1.25. Click “Enter.” And, then A page will display the router administration user login page.
3. Type the corresponding user name and password on the login page.
Next, click “Sign In.” Hopefully, you can now log in and manage your account. Then proceed to set up your router.
There may be differences between router brands and models regarding their login administration address.
In this case, you need to know the address of your router’s administration interface before logging in.
The address is usually located on the bottom of the router. This is where you can view the router’s login information.
A router’s IP address is usually 192.168.1.25. Some routers now use English letters as their login addresses, for example, melogin.cn, falogin.cn, tplogin.cn, miwifi.com, etc.
In the general label, you’ll also find the administration address of the router on the management page, router IP, login address, and login IP fields.
You can, however, change this address. But, if you try to log in after being modified using your original address, you will not be able to.
So, how can you find the IP address of your router?
Computers and mobile phones can be connected to the router’s WiFi signal. And then you can view it through these devices.
Why I Cannot Access 192.168.1.25?
We have already explained that you can access the router settings by logging in at 192.168.1.25.
So, then how should we proceed if 192.168.1.25 does not open the router’s login page?
We will discuss the reasons and solutions for this issue. So, if you experience similar issues, you can try the following solutions.
We can roughly divide the reasons why 192.168.1.25 is unable to open the router’s setup interface into the following 5 categories:
Router Connection Problem
The computer, modem, and router should be connected with a network cable. Here’s an example:
Start by connecting the modem to an external telephone line or optical fiber. After that, connect the modem to the router’s WAN port using a network cable.
Through Wi-Fi, laptops and mobile phones can be connected directly to the router. Using a network cable, you will need to connect the router’s LAN port to the desktop computer.
URL Input Error in the Browser
There are often large search boxes on the home page of most browsers. In the search box, people usually enter 192.168.1.25. But that won’t open the login page.
You should enter 192.168.1.25 in the address bar of your browser. The address bar is found at the top of the browser.
Improper Local IP of the Computer
You should have already set the local IP address of the computer. However, you will be unable to access the router if the settings are incorrect.
Set the computer’s IP address for automatic retrieval as the solution. We will use a Win10 system to illustrate how the local IP is automatically acquired.
1. First, start by right-clicking the “Start” button in Windows 10. Then, click “Network Connections“. And, go ahead and open it.
2. Now, right-click on “Local Area Connection“. And, choose “Properties” to open.
3. Then, choose “Internet Protocol Version 4 (TCP/IPv4)“. And, continue clicking “Properties“.
4. Now, choose “Obtain an IP address automatically“. Then choose “Obtain DNS server address automatically“. And, press “OK“.
However, if the IP address of the computer is automatically acquired if it has never been set before then you can ignore this error.
Network Cable Problem
It is very likely that 192.168.1.25 will fail to open the router’s setup interface if there is a problem with the network cable used to connect the computer to the router.
So, to use the cable usually, you must make sure it is readily available. And, if you have spare cables at home, you can replace the damaged one with a working one.
To start, be sure to plug it in tightly. Try again if the router’s setup page cannot be accessed using 192.168.1.25.
Furthermore, suppose the network cable is faulty. In that case, you will notice an abnormal display of the network icon in the lower right corner of the computer.
It is possible to check whether the connection between the computer and the router is regular by looking at the icon or by directly running the CMD command “Ping 192.168.1.25” on the computer.
Router Setup Issue
Many users are mistakenly under the impression that all router’s default login IPs are 192.168.1.25. This is not always true.
Router addresses can vary with different brands and models. With an IP address other than 192.168.1.25, you will not be able to access your router’s setup page.
You must verify whether your router has the IP address 192.168.1.25. You can find this information on the bottom label of the router under the default IP address (URL).
Alternatively, the router’s default IP address may have been changed. Because to increase the router’s security, some users may modify the router’s default address.
So, 192.168.1.25 will no longer work after the modification. To view the actual login address, follow these steps:
1. Right-click the “Start” button in Windows 10. Then, click “Network Connections.”
2. Now, right-click on “Local Area Connection” And click “Status” to open.
3. Then, click on “Details.”
4. Now, locate the IP address behind “IPv4 Default Gateway“. This is the router’s actual login IP address.
Change the Router Passwords using 192.168.1.25
Changing the default router user name and password is usually necessary to ensure network security and prevent others from accessing the network.
It is described below how to change the wireless network password (WIFI password) and the router’s login password (192.168.1.25).
Change the Wireless Network Password
You can change the wireless network password (WIFI password) as you change the router’s login password.
When successfully logged in to the router at 192.168.1.25, click “Advanced.” Next, click “Setup.”
Now, click on “Wireless” And, click on “WPA-PSK/WPA2-PSK“. Then, type your PSK password (WIFI password). Then click “Apply.”
There are 3 authentication types. They are automatic selection, WPA-PSK, and WPA2-PSK. But, there is basically no difference between the 3 types. Just select the automatic option.
There are also 3 encryption algorithms. And they are automatic selection, TKIP, and AES. Here, the AES encryption algorithm is generally recommended.
Change the Router’s Login Password
The computer or mobile phone must be connected to the router wirelessly or via a network cable if you know the password.
You can open your router’s login page by typing 192.168.1.25 into the browser’s address bar. Then, you will then need to enter the router’s default username and password.
Once you have successfully logged into the router’s setup interface, click the “OK” button. And click on “Advanced” to see more options. Then, select “Administration.”
Now, click on “Set Password.” And type in your new username and password. Click Apply.
You can only successfully log in to the router after changing the administrator login password. It is also, therefore important that you remember this password.
So, write it down in a safe place. Also, to prevent forgetting the password, you can paste it to the back of the router.
Restore the Factory Settings of Routers using 192.168.1.25
Using 192.168.1.25 to access the router administration page, how do you reset the router and restore the factory settings if the router settings are messed up, and you cannot access the Internet usually?
Generally, there are two methods for restoring factory settings:
Press Reset Button
You can reset the wireless router by pressing the Reset button on the back. There are typically two forms of the Reset button.
There is a protruding button that can be pressed directly. Another button has a small hole in it.
To use, insert a paper clip, pin, or another fine-pointed object into the hole and press continuously.
After you turn on the router, press and hold the buttons for about 10 seconds, and the indicators will be on.
The router will then begin working again after a few seconds. And this indicates that it has been successfully restored to factory settings.
Restore Factory Settings using 192.168.1.25
1. Go to your computer or mobile phone’s browser. Then, enter 192.168.1.25 into your browser’s address bar. And click “Enter.”
2. To access the router administration page, enter your username and password.
3. On the router’s administration page, different brands and models have different menus and buttons.
4. Then, locate “Advanced.” And click on “Administration.” Then click “Backup Settings.”
5. Now, click “Reset to Factory Defaults“, Here, you will be asked if you want to restore the factory settings to avoid misoperation or affecting Internet access.
6. Press the “OK” button. Then, the router will restart on its own. And factory settings will be restored after the reboot.
Final Words
This is about 192.168.1.25 Admin Login Page, Username, Password, and WiFi Settings. We hope that we have answered all of your queries. Do comment and share your suggestions or ask questions. We are here to help.
RELATED ARTICLES:
